does anyone have oscilloscope data for series I rx8 wheel speed sensors?

I am trying to use haltech for traction control and it's asking sensor voltage at 500, 1k, 2k, 3k, 4k, 5k, and 7k wheel revolution. I don't have any oscilloscope to find out.. does anyone have this data handy for our wheel speed sensors? Thanks in advance.

does anyone have oscilloscope data for series I rx8 wheel speed sensors?

{ FS } DEFI EGT Guages (2)

For Sale:

(2) DEFI EGT Guages. 52MM White - DF06803

Racer Gauge Lineup 2 1/16in(52mm) gauges | Defi - Exciting products by NS Japan

They come with wiring and EGT sensors. What is not included in the weld bungs. The weld bungs are on my exhaust manifold that I have for sale.

Text works best for way of contact.

Thanks!

Neal

Attached Thumbnails

   

{ FS } DEFI EGT Guages (2)

NA SemiPP 20b

This is more of a place holder for now. Engine is purchased, but won't be ready till around June / July. Then it's off to the fabricator to get it in the car. Lastly wiring and tune.

Goal 350-450WHP NA
Preferably over 400WHP (very possible). 450WHP not likely (being a realist)


Mazmart
B series motor purchased. Reliable source, and on the shelf.


Built by Myles Fisher
9.7 NA rotors
1" ID Semi PPort
Undecided on modifying the stock ports. Will probably need to in order to meet goal WHP range.


Fabrication by Coffee Fabrication
Undecided on intake and LIM design
90MM DBW throttle body
Flaming River custom steering rack. Little faster ratio than stock
MK3 MR2 Electric power steering pump
Undecided on hooking up the speed sensor to the pump


Wiring by LMS-EFI
AEM 710 ECU
Stock ECU retention for OBDII readiness checks, AC, etc
Relocate both ECUs from the engine bay
Full engine bay rewire and wire tuck
Maybe relocate / hide stock fuse box

NA SemiPP 20b

{WTB} Driver Door Wire Harness & Dash Peice

I am in need of a Drivers door wire harness. And a panel off the dash. The one that goes around the cluster, text would be easier. 715-817-0662

Thank You

{WTB} Driver Door Wire Harness & Dash Peice

{ FS } Strut Bar/ Mazadaspeed wing

for sale
ebay front strut bar $50



re-paint red instead of orange

04 05 06 07 08 09 MAZDA RX8 FRONT STRUT TOWER BAR RX-8

Mazdaspeed wing (replica) painted 05 BB $350 comes with both sections and hardware. bought a authentic so i don't need this anymore. (might keep it as spare)



located in Barrie ON.

{ FS } Strut Bar/ Mazadaspeed wing

Misfire... after swap

okay so I had a very bad misfire and the engine would stall, and then not want to restart.

I swapped the coil harness connectors (very limited info for correct order anywhere)

It now runs fine after 3000 RPM but at low RPM has trouble making power and sometimes will die at idle

I have an extra set of coils and wires that I've swapped that makes no difference

I have changed the plugs twice to no avail

One thing I am concerned with is the injector plugs on the intake manifold I was able to find that a blue one is on the top, correct?

And there is a black and white plug underneath them I have no idea what order they go in.

Could that be what's causing this issue?

Misfire... after swap

02 sensor harness plug

Ok I just did an engine swap and I see my front stream 02 sensor plug is not connected to anything!

Can someone help me find which/where the harness plug I need to plug into is?

Location, and or color of wires would help greatly.

Of course I've searched the forums and Google and I'm not finding what I need

Many thanks

02 sensor harness plug